Keywords:  *
J40 series ConnectorTotal > CONNECTORS > D-SUB (Rectangle) > J40 series
J40 series Connector
The connector includes 7 types of contacts:11、13、15、25、31、39、51 cores. Using twist wire spring pin (twist pin), and widely using for electric connector of the top of bomb electric equipment and the main computer or electric connector within any kinds of mini electric equipment.
Product solid pictureJ40 series J40 seriestop ↑
J40 series J40 series
J40 series Connectors Product solid pictureJ40 series Connectors Product solid picture
J40 series J40 series
brief introductionJ40 series J40 seriestop ↑
J40 series J40 series
  ? The products are characterized by flexible pin and reliability contacts( High density)
  ? Including seven types of contact:11?13?15?25?31?39?51cores
  ? The section area of cable is 0.20mm2~0.35mm2
  ?  The Performance Standards:
    Q/Ln.J6-72-93  Specification for J40 subminiature rectangular connectors
    Q/Ln.J6-131-2000  Standard for J40 subminiature rectangular connectors
J40 series J40 series
specificationJ40 series J40 seriestop ↑
J40 series J40 series
Ambient Temperature Range
-55~+125 ?
Relative Humidity
Up to 90% at +40?
Low Voltage
0.3kPa   100V
Vibration
10~2000 Hz   150m/s2
Radom Vibration
Power density 0.4G2/Hz  total acceleration-root-mean square is 23.1G
Shock
735 m/s2
Acceleration
500 m/s2
Current Rating
5A
Contact Resistance
=10 mO
Insulation Resistance
=5000 MO
Dielectric Strength
1000 V
Durability
500 times
J40 series J40 series
how to orderJ40 series J40 seriestop ↑
J40 series J40 series

    J40  - ×   TJ/ZK   ×    ×  -  ×   (covering)
     ?      ?     ?      ?    ?     ?    
      ?:J40 — Series Prefix
      ?:× — Number of Contacts:11?13?15?25?31?39?51
      ?:TJ/ZK —Type of Connectors and Contacts:TJ-- Pin in the plug   ZK-- Socket in the receptacle
      ?:× — Mounting Mode:No designator for crimp?S -- Solder?N – in-line for PCB?W – Right Angle for PCB
      ?:× — Type of Hardware:Q – Bayonet fast locking set; used with type“K” bayonet fast locking bolt?Q1 – Short bayonet fast locking set; used with type“K” bayonet fast locking bolt?K -- Bayonet fast locking bolt,used with type “Q” bayonet fast locking set or type “Q1” bayonet fast locking set?P -- Installation bolt; used with type L locking bolt?P2-installation bolt, suitable for installing from back board, used with type“L2” locking bolt; L -- locking bolt; used with Type P installing bolt; L2-locking bolt, used with type “P2”installation bolt.
      ?:× —special design : no designator for basic mode?A – on the surface of the plug and receptacle has no flange in the width direction,needing suitable hardware ?B –the plug with two installation holes for f2.2 unthreaded holes on the flange, and with a installation screw; the receptacle with installation screw ,sealed washer, wide flange with four installation holes for f2.2 unthreaded holes?C – the plug with right angle cable clamp and installation screw; the receptacle with rubber washer and installation screw?D –the plug, receptacle with right angle cable clamp, needing suitable hardware , E/EI-the flange is widen , and with error proof function; K – the plug ,receptacle with two installation holes for f2.2 unthreaded holes on the flange, needing suitable hardware; TJ1/ZK1-the section area of cable for crimp contacting is 0.10mm2~0.15mm2, and the shell is the same with TJ/ZK.
Note :the covering is not included in the ordering information, please mark the cable type in the bracket. For example: the section area, the length and the color of cable. If the relative of connecting cable is complex, please give the connecting cable table.
      Note:1?There are only two types of connectors and contacts: “TJ” and “ZK” ;
                2?Among the retaining members type “Q”?type “Q1” and type “K” are suitable for 11 cores and 13 cores connectors only ;
                3?The variation type “-D” is suitable for 11 cores and 13 cores connectors only.
For example
 J40  - 25   ZKS   P      (covering)
   Means the number of contact is 25, socket in receptacle, the termination style is solder wire, with type P installation bolt. (covering: the section area, length and color of cable, etc)

J40 series J40 series
Contact ArrangementsJ40 series J40 seriestop ↑
J40 series J40 series
 The hole position arrangement viewed from pin connector termination side.
J40 series Connectors Contact Arrangements
J40 series Connectors Contact Arrangements
?=core

 

J40 series J40 series
The Family TreeJ40 series J40 seriestop ↑
J40 series J40 series

Plug (receptacle) accessories
J40 series Connectors The Family Tree
Retaining member
J40 series Connectors The Family Tree
Instruction
J40 series Connectors The Family Tree
The plug (receptacle) must be ordered with retaining member at the same time, so that it is a whole connector.

J40 series J40 series
Product FamilyJ40 series J40 seriestop ↑
J40 series J40 seriesJ40 solder contact connectors
Contacts and cables is solder contact;
J40 Crimp Contact Series
Contacts and cables is crimp contact;
J40 Variation Connectors
Contacts and cables is crimp contact or in-line contact for PCB; 3 variation connectors for J40 : “-A、”、“-B”、“-C”.
J40 Retaining Member
7 types : Type Q、Type Q1、Type K、Type P、Type P2、Type L、TypeL2
Panel cutouts of J40 connectors

J40-E connectors

J40 series J40 series